RF 신호 레코드 플레이백 시스템
엘텍에서 제공하는 RF 신호 레코드 플레이 시스템을 소개 합니다.
X-COM 시스템의 RF 스트리밍 솔루션은 확장 가능하고 고속이며 지속적인 캡처 및 저장 솔루션을 제공합니다.
휴대용 디자인으로 실험실과 현장 테스트 환경에서 모두 RF 신호 레코더로 사용할 수 있습니다.
당사 시스템은 최대 1GHz의 순간 대역폭으로 DC에서 50GHz까지의 스펙트럼을 기록합니다.
X-COM의 고해상도 장시간 RF 신호 저장 및 재생성 기능은 많은 테스트 및 측정 산업 리더의 스펙트럼 분석기 및
벡터 신호 발생기의 성능을 극적으로 높일 수 있습니다.
APPLICATIONS
Interference analysis
Electronic warfare
Surveillance
Spectrum management
Forensics
Design validation
RF RECORD INTERFACE – I and Q INPUTS
Each IQC91000A system includes:
(1) IQC91000A single channel signal recorder
(1) IQC90000A-101 analog differential baseband IQ outputs
(1) IQC90000A-DC5 down converter
(4) IQC90000A-MEM interface adapters to external disk storage units
(2) IQC90000A-S15 external RAID0 SSD external storage disks
(1) IQC91000A single channel signal recorder
(1) IQC90000A-101 analog differential baseband IQ outputs
(1) IQC90000A-DC5 down converter
(4) IQC90000A-MEM interface adapters to external disk storage units
(2) IQC90000A-S15 external RAID0 SSD external storage disks
SIGNAL RECORD
Recording Channels: 1
Center Frequency: 1 to 18 GHz
Record Bandwidth: 1000 MHz @ 4 dB max
Frequency Tuning Resolution: 1 kHz
Record Sample Rate: 3.2 GS/s | Resolution: 12 bits
Gain Adjustment Range: 10 to 30 dB | Resolution: 1.0 dB
Full-Scale Amplitude: +3 dBm, (input signal + gain)
1 dB Compression Point: -5 dBm typical, at + 15 dB gain
3rd Order Intercept Point: -5 dBm typical, at + 15 dB gain
Amplitude Flatness: ±2 dB
Average Noise Level
@ 1 GHz: -160 dBm/Hz, with 30 dB gain
@ 4 GHz: -162 dBm/Hz, with 30 dB gain
@ 10 GHz: -160 dBm/Hz, with 30 dB gain
@ 16 GHz: -160 dBm/Hz, with 30 dB gain
Spurious Free Dynamic Range: >50 dB, with 0 dB gain
Noise Figure, with 30 dB gain
13 dB, 500 MHz – 7.9 GHz
14 dB, 7.901 – 10.1 GHz
13 dB, 10.101 – 17.499 GHz
16 dB, 17.5 – 18.5 GHz
Input Connector: SMA Female, 50 Ohms
Input VSWR: <2.5:1
Recording Modes: Manual, Timed, Triggered, Time of Day, Gated Record
Center Frequency: 1 to 18 GHz
Record Bandwidth: 1000 MHz @ 4 dB max
Frequency Tuning Resolution: 1 kHz
Record Sample Rate: 3.2 GS/s | Resolution: 12 bits
Gain Adjustment Range: 10 to 30 dB | Resolution: 1.0 dB
Full-Scale Amplitude: +3 dBm, (input signal + gain)
1 dB Compression Point: -5 dBm typical, at + 15 dB gain
3rd Order Intercept Point: -5 dBm typical, at + 15 dB gain
Amplitude Flatness: ±2 dB
Average Noise Level
@ 1 GHz: -160 dBm/Hz, with 30 dB gain
@ 4 GHz: -162 dBm/Hz, with 30 dB gain
@ 10 GHz: -160 dBm/Hz, with 30 dB gain
@ 16 GHz: -160 dBm/Hz, with 30 dB gain
Spurious Free Dynamic Range: >50 dB, with 0 dB gain
Noise Figure, with 30 dB gain
13 dB, 500 MHz – 7.9 GHz
14 dB, 7.901 – 10.1 GHz
13 dB, 10.101 – 17.499 GHz
16 dB, 17.5 – 18.5 GHz
Input Connector: SMA Female, 50 Ohms
Input VSWR: <2.5:1
Recording Modes: Manual, Timed, Triggered, Time of Day, Gated Record
DATA STORAGE
Capacity: 30 TB, configured as two 15 TB RAIDs
Storage Time: 90 minutes @ 1000 MHz BW
Data Format: Binary packed 12 bit signed integers, RAIDO formatted as EXT4
Data Offload Speed: >500 MB/s, subject to source computer and storage device
Data Offload Format 16 bit signed integers
Data Upload Speed: >150 MB/s via PCIeGen2 x8, subject to source computer and storage device
Data Upload Format: 16 bit signed integers
Storage Time: 90 minutes @ 1000 MHz BW
Data Format: Binary packed 12 bit signed integers, RAIDO formatted as EXT4
Data Offload Speed: >500 MB/s, subject to source computer and storage device
Data Offload Format 16 bit signed integers
Data Upload Speed: >150 MB/s via PCIeGen2 x8, subject to source computer and storage device
Data Upload Format: 16 bit signed integers
SIGNAL PLAYBACK
Output Signal: TTL Logic Levels: 0 to 3.3, 5 maximum
Playback Bandwidth: 1000 MHz, 500 MHz for I and 500 MHz for Q
Playback Sample Rate: 1.6 GS/s each I and Q
Playback Resolution: 12 bits
Amplitude, Full Scale: 500 mVp-p differential
Amplitude Flatness: ±2 dB
Number of Channels: 1000 per marker input per marker edge
Output Connectors: SMA Female x4
Output Impedance: 100 ohm differential
Playback Modes: Manual, Triggered
Playback Bandwidth: 1000 MHz, 500 MHz for I and 500 MHz for Q
Playback Sample Rate: 1.6 GS/s each I and Q
Playback Resolution: 12 bits
Amplitude, Full Scale: 500 mVp-p differential
Amplitude Flatness: ±2 dB
Number of Channels: 1000 per marker input per marker edge
Output Connectors: SMA Female x4
Output Impedance: 100 ohm differential
Playback Modes: Manual, Triggered
INPUTS and OUTPUTS
IF Input Connector: SMA Female
Amplitude: +3 dBm full scale
Center Frequency: 800 MHz
Reference Input Connector: BNC Female
Amplitude: 0 to +13 dBm
Center Frequency: 10 MHz ± 100 Hz
Reference Output Connector: BNC Female
Amplitude: +3 dBm nominal
Center Frequency: Equivalent to Reference Input
10 MHz Output Connector: BNC Female
Amplitude: 0 dBm, nominal
Center Frequency: 10 MHz ± 20 Hz
Amplitude: +3 dBm full scale
Center Frequency: 800 MHz
Reference Input Connector: BNC Female
Amplitude: 0 to +13 dBm
Center Frequency: 10 MHz ± 100 Hz
Reference Output Connector: BNC Female
Amplitude: +3 dBm nominal
Center Frequency: Equivalent to Reference Input
10 MHz Output Connector: BNC Female
Amplitude: 0 dBm, nominal
Center Frequency: 10 MHz ± 20 Hz
TRIGGER
Connector: SMA Female
Functions: Start/Stop Record | Start/Stop Playback
Impedance: 10 kOhms
Input Level Range: 0 to 5 V
VIH (input on threshold) = 1.7 V (min) and VIL (input off threshold) = 0.7 V (max)
Over Voltage Protection: Over voltage protection of +11 Volts and max under voltage of -6 Volts
Record Latency: -25 ns
Record Uncertainty: ±8 samples (±5 ns at full rate)
Gated Trigger Re-arm Time 20 ns
Functions: Start/Stop Record | Start/Stop Playback
Impedance: 10 kOhms
Input Level Range: 0 to 5 V
VIH (input on threshold) = 1.7 V (min) and VIL (input off threshold) = 0.7 V (max)
Over Voltage Protection: Over voltage protection of +11 Volts and max under voltage of -6 Volts
Record Latency: -25 ns
Record Uncertainty: ±8 samples (±5 ns at full rate)
Gated Trigger Re-arm Time 20 ns
MARKER
Connector: SMA Female, can be used in either record or playback modes
Impedance: 10 kOhms
Input Level Range: 0 to 5 V
VIH (input on threshold) = 1.7 V (min) and
VIL (input off threshold) = 0.7 V (max)
Over Voltage Protection: Overvoltage protection of +11 Volts and max undervoltage of -6 Volts
Latency: -25 ns @ 2.001 to 18 GHz (-37 ns 0.5 to 2.0 GHz)
Uncertainty: ±8 samples (±5 ns at full rate) at all frequency bands
Marker Re-arm Time: 20 ns
Total Available Per File: 100000
Content: Date, time of day, latitude, longitude, elevation sample number
Timing Sources: IRIG-B122, GPS via NMEA sentences w/1 PPS Marker input, PC-Time
Impedance: 10 kOhms
Input Level Range: 0 to 5 V
VIH (input on threshold) = 1.7 V (min) and
VIL (input off threshold) = 0.7 V (max)
Over Voltage Protection: Overvoltage protection of +11 Volts and max undervoltage of -6 Volts
Latency: -25 ns @ 2.001 to 18 GHz (-37 ns 0.5 to 2.0 GHz)
Uncertainty: ±8 samples (±5 ns at full rate) at all frequency bands
Marker Re-arm Time: 20 ns
Total Available Per File: 100000
Content: Date, time of day, latitude, longitude, elevation sample number
Timing Sources: IRIG-B122, GPS via NMEA sentences w/1 PPS Marker input, PC-Time
IRIG
Connector: BNC Female, can be used in either record or playback modes
Standard: IRIG-B122
Voltage Levels: Amplitude modulated, 3 Vpp, sine wave carrier
Over Voltage Protection: Over voltage protection of +11 Volts and max undervoltage of -6 Volts.
Standard: IRIG-B122
Voltage Levels: Amplitude modulated, 3 Vpp, sine wave carrier
Over Voltage Protection: Over voltage protection of +11 Volts and max undervoltage of -6 Volts.
GPS NMEA
Connector: 9 pin D Female, can be used in either record or playback modes
Speed: 4800 and 9600 baud
Supported Sentences: GPGGA, GPVTG, GPZDA
Protocol: ASCII, 8-bit data, one start and one stop bit, no parity
Speed: 4800 and 9600 baud
Supported Sentences: GPGGA, GPVTG, GPZDA
Protocol: ASCII, 8-bit data, one start and one stop bit, no parity
SYSTEM CONTROL – SYNCHRONIZATION
System Requirements (min): Windows 7, 8, 8.1, 10, Server 2012, 64 bit, 8 GB RAM
System Requirements (recommended):
Option IQC90000A-WS1: Rack-mounted SigAnalyst Workstation, Dual Xeon, Quad- Core Workstation, 64GB RAM with 128 TB HDD Storage Archive (96 TB usable). RAID60
Communication Interface Standard: LAN TCP/IP Interface
Communication Interface Speed: 1000 Base-T
System Re-Arm Time: 4 Seconds (without markers) when using API
Trigger Timing Uncertainty Between any Two IQC91000A Systems: ±7.8ns
Same 10 MHz reference and trigger signals must be applied to all IQC91000A systems
System Requirements (recommended):
Option IQC90000A-WS1: Rack-mounted SigAnalyst Workstation, Dual Xeon, Quad- Core Workstation, 64GB RAM with 128 TB HDD Storage Archive (96 TB usable). RAID60
Communication Interface Standard: LAN TCP/IP Interface
Communication Interface Speed: 1000 Base-T
System Re-Arm Time: 4 Seconds (without markers) when using API
Trigger Timing Uncertainty Between any Two IQC91000A Systems: ±7.8ns
Same 10 MHz reference and trigger signals must be applied to all IQC91000A systems
POWER
System Warm Up Time: 30 minutes
IQC91000A: 100/120 or 220/240 VAC, 50/60 Hz, 400 W max
option IQC90000A-DC5: 100/120 or 220/240 VAC, 50/60 Hz, 30 W max
option IQC90000A-MEM: 100/120 or 220/240 VAC, 50/60 Hz, 72 W max for each unit
option IQC90000A-S15: 100/120 or 220/240 VAC, 50/60 Hz, 130 W max
option IQC90000A-UC1: 100/120 or 220/240 VAC, 50/60 Hz, 650 W max
IQC91000A: 100/120 or 220/240 VAC, 50/60 Hz, 400 W max
option IQC90000A-DC5: 100/120 or 220/240 VAC, 50/60 Hz, 30 W max
option IQC90000A-MEM: 100/120 or 220/240 VAC, 50/60 Hz, 72 W max for each unit
option IQC90000A-S15: 100/120 or 220/240 VAC, 50/60 Hz, 130 W max
option IQC90000A-UC1: 100/120 or 220/240 VAC, 50/60 Hz, 650 W max
ENVIRONMENTAL
Conformity
Designed for compliance with test methods aligned with IEC 60068-2 and have humidity, shock, vibration, altitude, and power line condition levels similar to MIL-PRF-28800F Class 3
Temperature Range
Operating: 0 to 35 °C | Storage: -20 to +70 °C
Altitude: Max 2000 m above sea level
Humidity: Max 80% non-condensing
Designed for compliance with test methods aligned with IEC 60068-2 and have humidity, shock, vibration, altitude, and power line condition levels similar to MIL-PRF-28800F Class 3
Temperature Range
Operating: 0 to 35 °C | Storage: -20 to +70 °C
Altitude: Max 2000 m above sea level
Humidity: Max 80% non-condensing
DIMENSIONS
(H x W x D)
IQC91000A: 3.5″ x 16.5″ x 19.5″
option IQC90000A-DC5: 1.75″ x 17″ x 21.25″
option IQC90000A-MEM: 1.75″ x 12″ x 10.5″
option IQC90000A-S15: 3.5″ x 16.5″ x 17.75″
option IQC90000A-UC1: 7″ x 16.8″ x 20.3″
IQC91000A: 3.5″ x 16.5″ x 19.5″
option IQC90000A-DC5: 1.75″ x 17″ x 21.25″
option IQC90000A-MEM: 1.75″ x 12″ x 10.5″
option IQC90000A-S15: 3.5″ x 16.5″ x 17.75″
option IQC90000A-UC1: 7″ x 16.8″ x 20.3″
WEIGHT
IQC91000A: 22 lbs.
option IQC90000A-DC5: 13.5 lbs.
option IQC90000A-MEM: 5 lbs. for each unit
option IQC90000A-S15: 14 lbs. for each unit
option IQC90000A-UC1: 54 lbs.
option IQC90000A-DC5: 13.5 lbs.
option IQC90000A-MEM: 5 lbs. for each unit
option IQC90000A-S15: 14 lbs. for each unit
option IQC90000A-UC1: 54 lbs.
IQC91000A MODEL OPTIONS
IQC91000A: 1000 MHz single channel signal recorder with 800 MHz IF input and maximum digital IQ output rate of 4.8 GB/sec. Includes 4ea IQC90000A-MEM adapters with rack mounts, Control SW and documentation on CD.
IQC90000A-DC2: 3.6 GHz to 26.5 GHz down-converter with 700 MHz bandwidth centered at 800 MHz IF output.
IQC90000A-DC5: 1 GHz to 18 GHz down-converter with 1000 MHz bandwidth centered at 800 MHz IF output.
IQC90000A-101: Adds analog differential baseband IQ outputs for playback (4ea SMA female), 1000 MHz IQ bandwidth.
IQC90000A-DC2: 3.6 GHz to 26.5 GHz down-converter with 700 MHz bandwidth centered at 800 MHz IF output.
IQC90000A-DC5: 1 GHz to 18 GHz down-converter with 1000 MHz bandwidth centered at 800 MHz IF output.
IQC90000A-101: Adds analog differential baseband IQ outputs for playback (4ea SMA female), 1000 MHz IQ bandwidth.
MEMORY INTERFACE MODULE
IQC90000A-MEM: Interface Adapter to RAID0 external disk storage units. Four option MEM units are required per IQC90000A system
STORAGE OPTION
IQC90000A-S15: External RAID0 SSD external disk storage. Two data packs required per system for a total of 90 minutes storage at 1000 MHz bandwidth
CONVERTER OPTIONS
IQC90000A-UC1: 500 MHz to 18 GHz up-converter with differential IQ inputs for 1000 MHz output at carriers up to 18 GHz. Includes rack mount kit.
IQC90000A-UC2: 500 MHz to 40 GHz up-converter with differential IQ inputs for 1000 MHz output at carriers up to 40 GHz. Includes rack mount kit.
IQC90000A-UC2: 500 MHz to 40 GHz up-converter with differential IQ inputs for 1000 MHz output at carriers up to 40 GHz. Includes rack mount kit.
WARRANTY OPTIONS
IQC90000A-EX1: Extends factory warranty of IQC90000A by one additional year
IQC90000A-EX2: Extends factory warranty of IQC90000A by two additional years
IQC90000A-EX3: Extends factory warranty of IQC90000A by three additional years
IQC90000A-EX4: Extends factory warranty of IQC90000A by four additional years
IQC90000A-EX2: Extends factory warranty of IQC90000A by two additional years
IQC90000A-EX3: Extends factory warranty of IQC90000A by three additional years
IQC90000A-EX4: Extends factory warranty of IQC90000A by four additional years
WORKSTATION OPTIONS
IQC90000A-WS1: Rack-mounted SigAnalyst Workstation -Dual Xeon, Quad-Core Workstation, 64GB RAM with 128 TB HDD Storage Archive (96 TB usable).
IQC90000A-WS2: Rack-mounted SigAnalyst Workstation – Dual Xeon, Quad-Core Workstation, 64GB RAM with 128 TB HDD Storage Archive (96 TB usable), Spectro-X and RF Editor software packages.
IQC90000A-ENL: Rack enclosure to house IQC90000A, down converter, 2ea solid state data packs, upconverter, workstation, storage archive and power distribution.
IQC90000A-WS2: Rack-mounted SigAnalyst Workstation – Dual Xeon, Quad-Core Workstation, 64GB RAM with 128 TB HDD Storage Archive (96 TB usable), Spectro-X and RF Editor software packages.
IQC90000A-ENL: Rack enclosure to house IQC90000A, down converter, 2ea solid state data packs, upconverter, workstation, storage archive and power distribution.
SOFTWARE OPTIONS
WC-RF-EDITOR: RF Editor Signal Generation software
Spectro-X: Spectro-X Advanced Signal Analysis software
Spectro-X: Spectro-X Advanced Signal Analysis software
TRAINING OPTION
IQC90000A-TRN: Daily rate for onsite training and consulting by Bird Applications Engineer
Spectro-X는 사용자가 수 테라바이트 규모의 RF 데이터 기록을 걸러내어 사용자 입력에 따라 관심 있는 신호를 빠르게 식별할 수 있도록 하는 필수적인 신호 추출 도구입니다. 빠른 스펙트럼 검색을 통해 EASA 및 기존 레이더, ELINT, SIGINT, ECM, ESM, 다중 채널 통신, 원격 측정 및 MIMO 시스템을 개발하는 시스템 또는 테스트 엔지니어가 고해상도로 시각화하고 분석할 수 있습니다.
IQC5000B 또는 IQC91000A 신호 레코더와 결합하면 Spectro-X는 수 시간에 걸친 주의 깊은 스펙트럼 모니터링을 프로그래밍 없이도 빠른 사후 수집 검색, 마크 및 측정 작업으로 전환합니다.
Spectro-X의 세 가지 개별 검색 엔진인 캐리어, 임의 파형 및 펄스를 사용하여 캡처된 파일의 특정 섹션을 찾고 확대합니다. 대용량 녹음의 선택된 부분을 벡터 신호 분석 소프트웨어에서 복조 및 자세한 분석을 위해 사용할 수 있는 산업 표준 형식으로 IQ로 내보낼 수 있습니다.
제품 기능
최대 4개의 신호 파일(채널)을 동시에 찾아 분석합니다.
스펙트로그램 및 시간 영역 플롯으로 과도 이벤트를 감지합니다.
신호 매개변수를 시간과 주파수 모두로 표시합니다.
MATLAB 또는 기타 인기 있는 VSA 소프트웨어를 사용하여 신호 생성기로 파일을 재생합니다.
파일의 특정 부분을 확대하여 관심 있는 신호를 빠르게 식별합니다.
플롯당 무제한 마커. 채널 내 플롯에서 마커를 연결합니다.
펄스 설명자 단어는 펄스 열을 특성화합니다.
캐리어 검색은 지정된 시간 범위에 걸쳐 모든 고정 캐리어를 식별합니다.
사용자가 조정할 수 있는 채널 재생 오프셋은 하위 샘플 정밀도를 제공합니다.
마커 수학을 통해 채널 내 또는 채널 간에 시간 및 주파수 차이를 측정할 수 있습니다.
파일 기간에 제한이 없습니다.
다중 검색 엔진
캐리어 검색 – CW 및 고정 변조 캐리어
파형 검색 – 사용자 정의 참조 파형, I&Q 시간 도메인 매칭 라이브러리에 대한 검색
펄스 검색 – 상승/하강 시간, 펄스 폭, 펄스 반복 간격, 피크 및 평균 전력, 캐리어 주파수에 따라 펄스 파형을 검색하고 정량화
웨비나
Spectro-X 데모